Flooring

How Many Tiles Do I Need? Room Measurements, Waste and Boxes

6 min readLast updated November 16, 2026

A useful tile order starts with the surface receiving tile and ends with the actual packaging for one product. This worksheet follows the Tile Calculator: measured area, tile-face area, one waste allowance, then whole-box rounding. It does not lay out cuts or specify an installation system.

Measure the Surface That Will Receive Tile

Draw each floor or wall as non-overlapping rectangles. Record the length and width of a floor, or the length and height of a wall. A floor footprint is not the wall area of a shower. For several walls, add their separately measured areas.

Decide with the installer which fixed footprints or openings receive no tile. For an irregular outline or a deduction, calculate net area separately and use known total area. Do not subtract the same opening twice or mix floor and wall products in one box order.

Measure and combine sections with the Square Footage Calculator

Choose Room Dimensions or Known Total Area

For one rectangle, select Room or wall dimensions. In Imperial mode, enter whole feet and separate inches. Eight feet six inches is 8 + 6/12 = 8.5 feet, not 8.6 feet. Inches may be fractional but must be less than 12; enter 0 feet for dimensions shorter than one foot.

Metric room dimensions accept meters or centimeters. A 300 cm length is 3 m. Tile sizes use inches in Imperial and centimeters in Metric, regardless of the room-dimension unit. Switching measurement systems converts the existing project rather than replacing it with new defaults.

Use Known total area when you already have net square feet or square meters. For rectangular mosaics sold as a sheet, enter the saleable sheet dimensions and sheets per box. Irregular, interlocking or mixed-size products need manufacturer coverage and a separate layout rather than a rectangular tile-face approximation.

Turn Measured Area into Whole Tiles and Boxes

Tile face area is tile length multiplied by tile width. Divide square inches by 144 to get square feet, or square centimeters by 10,000 to get square meters. Divide project area by tile face area to obtain the base tile quantity.

Multiply the base quantity by 1 + waste percentage/100, then round up to whole tiles once. Divide that whole-tile count by the actual tiles per box and round up again to whole boxes. The calculator shows purchased tiles so you can see the extra quantity created by packaging.

Waste is a project input, not a guaranteed yield. The 10% used in these examples illustrates the calculation; confirm your allowance for the chosen tile, cuts, pattern, damage and retained spare stock. Do not add another waste percentage after box rounding.

Bathroom Floor: 8 ft 6 in by 6 ft

Enter length 8 feet and 6 inches, width 6 feet and 0 inches, and 12 × 12 inch tiles. Area is 8.5 × 6 = 51 sq ft. One tile covers 1 sq ft, so the base estimate is 51 tiles.

At an illustrative 10% allowance, 51 × 1.10 = 56.1: round up to 57 tiles. If the chosen product has 8 tiles per box, buy 8 boxes containing 64 tiles. Six-inch room measurements are not tile dimensions; keep the fields separate.

Backsplash: 10 ft Long by 18 in High

Enter length 10 feet and 0 inches, and width or height 1 foot and 6 inches. The rectangular surface is 15 sq ft. For 3 × 6 inch tiles, each tile face is 18/144 = 0.125 sq ft.

The base quantity is 120 tiles. With 10% waste, the estimate is 132 tiles. At 24 tiles per box, round 5.5 up to 6 boxes, containing 144 tiles. This example assumes no deducted openings. Measure separate splash sections and exclusions explicitly before using a combined known area.

Metric Floor: 300 cm by 240 cm

Select Metric and Centimeters for room dimensions. Enter 300 × 240 cm and 30 × 30 cm tiles. The surface is 7.2 m², each tile face is 0.09 m², and the base quantity is 80 tiles.

With 10% waste, the order is 88 tiles. At 10 tiles per box, buy 9 boxes containing 90 tiles. Changing room dimensions to Meters converts the fields to 3 × 2.4 without changing the estimate.

What to Check Before Ordering

This calculator divides by tile-face area and does not subtract grout-joint coverage. It does not count rows or optimize partial tiles, center a pattern, model a border, predict offcut reuse or calculate grout and thinset. A layout with actual tile dimensions and required joints remains a separate step.

Check the product SKU, actual dimensions, pieces and coverage per carton, shade or caliber, and lot availability. Reconcile package-label coverage with the face-area estimate; do not assume every product called 12 × 12 inches covers exactly one square foot.

A laser level can help mark reference lines, but it does not measure area, select joint width or establish substrate suitability. Confirm instrument specifications and installation requirements separately. Trim, waterproofing, substrate preparation, adhesive, grout and labor are separate order items.

Source and Product Checks

Tile America provides a feet-and-inches measuring worksheet and discusses project-dependent overage. This guide’s worked quantities are our own arithmetic examples. Use the selected product’s current carton information and installer’s layout to finalize the order.

Tile America — Calculate Square Footage

Use the Calculator

Get an instant estimate with the Tile Calculator

Enter room dimensions or known net area, actual tile dimensions, waste and package quantity to estimate whole tiles and boxes.

Open Tile Calculator

Frequently Asked Questions

Does 10% waste include rounding up to boxes?

Waste is applied first to the base tile quantity. Whole tiles and then whole boxes are rounded up. Purchased box surplus can exceed the exact waste allowance; it is not another waste factor.

Can I combine several rooms?

Yes, if they use the same product and purchasing assumptions: sum their net non-overlapping areas and enter that total in known-area mode. Separate products and incompatible layouts require separate estimates.

Will this tell me how to cut the tiles?

No. This is an area-based purchase estimate, not a row-by-row layout or cutting optimizer. Check joints, edge cuts, orientation and reusable offcuts separately.